The following custom device properties are available for configuration on the Local Managers.
Property | Description |
---|---|
sysContact.0 | When SNMP is enabled on the Local Manager, defines the system contact. |
sysLocation.0 | When SNMP is enabled on the Local Manager, defines the system location. Useful if the Local Manager is behind a firewall or NAT. |
sshPort | This property overrides the default port 22 for SSH connections. Useful if the Local Manger is behind a router with port forwarding capabilities. |
sshIp | This property overrides the reported IP address when initiating an SSH connection with the CLI applet. |
sshIpv6 | Specifies an alternate IPv6 address to be used instead of the address reported by the Local Manager. |
sshPortOob | This property overrides the default port 22 for SSH connections while the Local Manager is operating out-of-band. |
sshIpOob | This property overrides the reported out-of-band IP address. Useful if the Local Manager is behind a firewall or NAT when it brings up its out of band connection. |
sshIpv6Oob | Specifies an alternate IPv6 addressed to be used when the Local Manager is operating out-of-band. |
_csr_OU | For use when placing the Local Manager in FIPS mode, the property defines the Organization Unit required when generating a certificate. |
_csr_CN | For use when placing the Local Manager in FIPS mode, the property defines the Common Name required when generating a certificate. |
_csr_O | For use when placing the Local Manager in FIPS mode, the property defines the Organization required when generating a certificate. |
_csr_L | For use when placing the Local Manager in FIPS mode, the property defines the Location required when generating a certificate. |
_csr_ST | For use when placing the Local Manager in FIPS mode, the property defines the State required when generating a certificate. |
_csr_C | For use when placing the Local Manager in FIPS mode, the property defines the Country required when generating a certificate. |
_csr_E | For use when placing the Local Manager in FIPS mode, the property defines the Email Address required when generating a certificate. |
_csr_other | For use when placing the Local Manager in FIPS mode, the property defines other elements that the user may wish to include when generating a certificate. |
forwardIpAddress | Set IP address for forwarding inbound UDP packets. |
readCommunity | Configuration information specific to ND SatCom. |
writeCommunity | Configuration information specific to ND SatCom. |
Enhanced_CommandPrompt | Define an enhanced driver's command prompt. |
Enhanced_PasswordPrompt | Define an enhanced driver's password prompt. |
Enhanced_LoginPrompt | Define an enhanced driver's login prompt. |
Enhanced_LogoutCommand | Define an enhanced driver's logout command. |
Enhanced_TimeoutSeconds | Define an enhanced driver's timeout duration in seconds. |
Enhanced_WakeupCommand | Define an enhanced driver's command to wake up a managed device. |
safedelay | Define a delay period for use after a command is run. |
safeDebug | For use on Sea Tel devices, define for extra log messages on the console during Push OS. |
_powerOnValidationTimeout | Defines a time in milliseconds for the system to wait before checking CTS and DSR during a power on or power cycle operation. |
debug | For RFC-2217 "TCP" connections and/or virtual ports set property for extra log messages on the console. |
_keepalive | For use with virtual ports on Cisco devices, configure a message or character to be sent to maintain the connection. |
ROMMON* | During a ROMmon recovery, ROMmon variables defined in this property will be passed to the Cisco device. |
remoteHostOrIpAddress | For use when connecting to an IP address or port via the management Ethernet on the Local Manager, this property defines that destination host or IP Address. |
tcpPort | For use when connecting to an IP address or port via the management Ethernet on the Local Manager, this property defines that destination port. |
_applet_failover_ssh_ip | Set the failover SSH IP address when configuring the CLI applet to failover directly to a managed device. |
_applet_failover_ssh_port | Set the failover SSH port when configuring the CLI applet to failover directly to a managed device. |
_applet_failover_ssh_fingerprint | Set the SSH fingerprint when configuring the CLI applet to failover directly to a managed device. |
_lcp_echo_interval | Define the value in seconds between LCP echo requests. Set property to 0 to disable LCP echo. |
_lcp_echo_failure | Define the number of subsequent failures before a PPP link goes down. |
_modem_monitor_init | This property overrides the modem initialization string on the modem monitor. |
_modem_monitor_test | This property provides a test dial string on the modem monitor. |
_snmp_1.3.6.1.4.1.10243.10.1.5.5 | Set to "enable" if customer has a GPS attached to their Local Manager and would like the statistics to show up in SNMP. |
_snmp_.1.3.6.1.4.1.2021.10.1 | Set to "enable" to get SNMP Load Average (UCD-SNMP-MIB). |
_snmp_.1.3.6.1.2.1.25.2.3.1.1.1 | Set to "enable" to get SNMP Memory Info (HOST-RESOURCES-MIB). |
_snmp_.1.3.6.1.2.1.25.2.3.1.1.31 | Set to "enable" to get SNMP Disk Info (HOST-RESOURCES-MIB). |